این کار باعث حذف صفحه ی "If the Juices are not Clear" می شود. لطفا مطمئن باشید.
Grilling is ideal for cooking smaller pork cuts, such as chops, steaks, ham slices, tenderloins, ribs, ground pork patties, sausages, and kabobs. Because grilling uses high heat and short cooking times, it tends to toughen the meat, so it is best to use the most tender cuts available. Lean pork cuts will benefit from marinating before they are grilled. Pork steaks and pork chops that are going to be grilled should be a minimum of ¾ to 1 inch thick because the high heat will cook the meat quickly. If the cuts are thinner than this, it is easy to overcook the meat, causing it to dry out. The meat must be watched carefully while grilling. Coating the pork with a little oil or marinating it before cooking will help keep it moist. It is important that the grill be properly preheated so that it seals the juices into the meat quickly. The temperature at which the pork is cooked and the distance it is placed from the heat source are both important for providing tender, juicy, properly done pork.
The grilling process cooks foods over a high heat source, either directly, indirectly, or a combination of both. Grilling temperatures typically reach as high as 650ºF, but any temperature above 300°F is suitable as a grilling temperature. The high heat of grilling sears the surface of pork, creating meat with a flavorful crust. The required cooking temperature and the method of grilling (direct, indirect, or a combination) depends on the cut of pork and the quality of the meat. Because pork today is raised to be very lean, it is important it is not overcooked in order to produce the best results. There are many different types of grills available today that can be used when grilling pork. For information on the different types of grills, see Types of Grills. It is important that the grill is set up properly and reaches the appropriate temperature for the cut of pork that is being grilled to ensure that it produces in a juicy, tender finished product that is cooked to the proper doneness.
For information on setting up a charcoal or gas grill, see Outdoor Grill Preparation. When grilling, pork should be cooked at a medium heat. For information on checking the temperature of the grill, see Estimating Heat Level.. The thicker the cut the farther away from the heat source it should be or the heat source should be at a lower temperature to prevent the outside of the cut from burning before the inside is properly cooked. You will also have to decide whether you will use direct or indirect heat during the grilling time. Depending on the cut, you may use both. A cut of pork may require direct heat to seal the outside and indirect to allow the cut to cook thoroughly to the center. Cooking with indirect heat occurs when you use an area of the grill that is not directly over the heat source. Using indirect heat slows the cooking process down, which allows the center of the cut to cook thoroughly without burning the outside.
On charcoal grills, coals are pushed to one side of the grill or banked into a ring around the outer edges. On gas grills, the side of the burner, which is below the area where the food will be placed, is turned off after the grill is preheated. Using one of the indirect setups will provide an area on the grill that is a low heat source. The meat is placed over the area in which there are no coals or over the burner that is turned off on a gas grill. Indirect heat is good for cooking larger cuts of meat, such as roasts, ribs and ham. Once the meat is prepared and the charcoals have been heated properly (see Charcoal Rocket Chef Turbo Grill Review Setup), there are several easy steps to follow in order to cook pork with indirect heat on a charcoal grill. There are different setups that can be used for indirect grilling on the charcoal grill. The coals can be pushed to one side of the grill and a pan placed on the opposite side.
The pan is used to catch the fat as it melts and drips from the meat while cooking. This will help reduce flare-ups. An alternative method for arranging coals for indirect heat grilling is to place half the coals on one side of the grill and the other half on the opposite side. Some charcoal grills are equipped with side baskets, which can be used for this purpose. A drip pan is placed between the coals in the location where the meat will be cooked. A third method of arranging the coals is to bank them into a ring around the outer edges. Again, a drip pan is placed in the middle of the coals and when the grate is placed on the grill, this is the area the meat will be placed on the grate. When using any of the indirect methods, the pork is generally cooked with the cover on the grill. Any of the indirect charcoal grill setups provide an area on the grill, directly above the drip pan and away from the coals, that creates the indirect heat area.
این کار باعث حذف صفحه ی "If the Juices are not Clear" می شود. لطفا مطمئن باشید.